ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel

D.I.Y. house repairs

Updated on April 25, 2020

Brisbane typical old timber houses

This is  a typical workers cottage in Brisbane, it is a smaller version of the real Queens-lander just because it is small and more affordable. Anyhow this is how my house was like when it was near new, but today it went through some alterations.
This is a typical workers cottage in Brisbane, it is a smaller version of the real Queens-lander just because it is small and more affordable. Anyhow this is how my house was like when it was near new, but today it went through some alterations. | Source
Back of the house, here also we had to change a couple of timber treads.
Back of the house, here also we had to change a couple of timber treads. | Source

Timber houses repairs or renovations

Welcome to our article, (43), D.I.Y. house repairs.

Timber houses repairs or renovations

Dear readers, in our DIY articles we have talked about, how to lay bricks in, DIY brickwork , and other articles about building, the last one, Bricklaying needs to be competitive. In this article, we want to talk about house repairs and renovations. Since we have talked about brickwork, concrete work and block work, but today we are going to change, it will be a mix up of trades including timber work.

You see, if you want to do any job on old houses, you need to know how to do a bit of this and a bit of that, so, you don’t need to be a carpenter to cut a few pieces of timber, drive a few nails, paint the house or build a wall.

Because, if the work is for your house, you do not need to be a tradesman, except for those trades that are forbidden from bylaws, since it is dangerous if you make mistakes; like electrical work or plumbing work. So, don’t do electrical work, except changing a light bulb, and plugging in any electrical devices; plumbing work you can change a tap washer valve, or unblock the kitchen sink drain, if you have the right tools, and that’s all. Other trades you can do it ourselves.

Anyhow, let us talk about what we can do ourselves, if we own a timber house say in Queensland; we want to talk about Queensland houses, because that is the place I have been living for many years and I am writing from, therefore, I know most about what can be done here legally, in other parts of the world it can be different.

Now let us talk about the timber houses, the timber houses need a lot more maintenance than the brick and masonry buildings, because they need to be painted regularly, otherwise the exposed timber outside can rot, and then you need major repairs, but not everything affects these timber houses in a negative way, because they are easier to fix and to do alterations, compared to bricks and mortar buildings, so, let us see what most people can do, if they own a timber house and they want to repair it, or do renovation and alterations. Now, let us talk about the latest work I have done, which was replacing some flooring on the veranda and then replace a set of old timber stairs with concrete treads. To replace the timber flooring was easy, because you need to pull the old rotten board out and replace them with new ones, to replace the stairs was a lot harder, because first I had to decide what I wanted to use, as the existing stairs were rotten beyond repair, but let us see what I did.

New concrete treads and stringer have replaced the old timber one

The set of concrete stairs on galvanized steel stringers have been finished, and I believe that they will last for 50 years maintenance free, I have fixed the old hand rail, as it could last for another 20 years and that will do me just fine.
The set of concrete stairs on galvanized steel stringers have been finished, and I believe that they will last for 50 years maintenance free, I have fixed the old hand rail, as it could last for another 20 years and that will do me just fine. | Source
These are the stairs that need replacing, they have been there since the house was built, my personal guess is that they are over eighty years old. So if they are falling apart we could not complain, if you look closely you see that they are falling.
These are the stairs that need replacing, they have been there since the house was built, my personal guess is that they are over eighty years old. So if they are falling apart we could not complain, if you look closely you see that they are falling. | Source

Repair or replace stairs

I am writing this article now, because after fixing the patio floor I had to replace the front stairs where I am living now; I knew that the stairs were rotting away and soon or later we had to replace them, but I was trying to delay it as much as I could, because stairs are not easy to build and anyone that attempts to fix or replace them will find it hard to do unless he knows how to build them. But since I am a bricklayer, I knew what to do.

But even though I knew what to do, because of the several set of brick stairs that I have built as a bricklayer, I did not like to do this job. However, one day I saw that the timber stairs were becoming dangerous, because the timer stringers were rotting away and some of the treads were just about to fall out or break if a heavy weight got on them, so, this job that I was trying to delay suddenly became urgent, because this steel brace that was holding them tight together suddenly broke.

I did not want to replace this set of timber stairs with brick stairs, because brick stairs are very expensive, they take a lot of bricks, a lot of concrete and a long time to build, you see, brick stairs are build where a building is made of bricks. We can say that they are the most expensive to build using just simple building materials. Now at the same time I did not want to get somebody to make new timber stairs because today they are very expensive and the timber is not of that grade that lasts a long time, as it used to be.

The story of this set of old timber stairs is thus; I have been living in this house for a long time, and over twenty years ago I fixed this same set of stairs that were rotting at the bottom by cutting a few treads at the bottom and then building a concrete pathway higher than the existing ground, this was easy to do because of the sloping ground, in fact, it worked out well because we did not have to walk first downhill and then walk up the stairs.

Replacing stairs with concrete treads

The older timber stairs have been removed  and we have replaced them with concrete treads.
The older timber stairs have been removed and we have replaced them with concrete treads. | Source

Replacing stairs with concrete treads

Now the problem is different because we need to replace all the steps. So, we want a new set of stairs that are not expensive, they must last a long time, they are almost maintenance free, so, how we can achieve that?

After thinking it over we decided to build a new set of stairs using concrete treads on a pair of galvanized steel stringers; you see these two types of material last a long time as they don’t rot and because of that they are mostly maintenance free; they are ready made and available if you shop around a bit in Brisbane QLD. Anyhow, I remember that a few years ago, I lot of suppliers had them in stock, today you must look for them.

Anyhow, it pays to look at direct supplies, because they may have a larger stock to choose from, so, I did, and I saved money as well. I bought my concrete treads from a concrete product supplier; this is their link;

Crosby Concrete Products - Domestic Concrete Step Treads ..,

Anyhow, I went there and picked them up and saved some money, you see it pays to shop around and see what your best deal is.

Crosby concrete products

I remember that once upon a time you could buy concrete treads in lost of places, today you have to look where you can buy them and they may vary in price as well, so one needs to ask the right questions and go to the right place to buy them.
I remember that once upon a time you could buy concrete treads in lost of places, today you have to look where you can buy them and they may vary in price as well, so one needs to ask the right questions and go to the right place to buy them.

A pair of tipycal steel stringers

This is a typical pair of steel stringers, they come in many sizes, all you have to know is how many treads you need before you buy them. They are also available in hot dip galvanized, but they are more expensive, I believe they are worth the cost
This is a typical pair of steel stringers, they come in many sizes, all you have to know is how many treads you need before you buy them. They are also available in hot dip galvanized, but they are more expensive, I believe they are worth the cost

Buying galvanized steel stringers

Next, I bought a pair of galvanized steel stringers from Scott Metal, here I did not save a lot, but they were the closest with a reasonable price, so, I went there and picked them up.

This is their web address; www.scottmetals.com.au/, Scott Metals, Woolloongabba Brisbane - Metal Manufacturers

I visited the closest hardware to buy some bags of concrete, these bags of ready to mix concrete cost more than is used to cost, but this is what is readily available today; I bought also a couple of galvanized brackets that I could lay in the concrete to hold the hand rail firmly up and some screws. These are the main materials that I needed to do the job, as for the handrail, I was using the old handrail. All I had to do is to fix the handrail to the timber post that would be fixed to the galvanized brackets at the bottom of the stairs, any other adjustment would be done while working on site. So, let us replace this set of stairs.

-------------------

One of the Scott Metal signs

Scot Metal is a company that deals in all sorts of steel supply
Scot Metal is a company that deals in all sorts of steel supply

Building new set of stairs

This is the new set of stairs partly built, as you can see the hand rail needs to be completed and then painted.
This is the new set of stairs partly built, as you can see the hand rail needs to be completed and then painted. | Source
This is the side of stairs, this photo was taken to show you the stringers and the side view.
This is the side of stairs, this photo was taken to show you the stringers and the side view. | Source

Describing our step by step procedure

Now that we have bought the materials that we need to replace this set of stairs, we are going to show you, how we did this job.

First, you need to remove the old set of stairs; but before you do that you need to know if there is anything that you can save, in my case I decided that I could save the old handrail, if I could keep it attached to the house and so I did. To do that, I cut all connection between the handrail and the rest of the stairs that had to be demolished. After doing that, I started to remove the old timber treads one by one, you see you need to be careful here, because they are heavy, and it is easy to get hurt. Anyhow, you need to use a sledgehammer to knock the treads out of there housing, because some of them may still have some old nails holding them in place. After you have removed all the treads you remove the old timber strings, here again you need to be careful specially if they are long and heavy.

Next step you make sure that the part of the house that you are attaching the new stringers is solid and if it is not fix or replace whatever it is needed. Then take one of the steel stringers and lift in position to see if it fits and where it ends, because you may have to dig a hole in the ground if your stringers have an in-ground leg. To do that, you should get your stairs approximately in the right position, once you have done that, you need to work out the height of the top step; because the top step needs to be the same height of the rest of the steps, so, this is one of the critical measurement, the other one is the distance between the two stringers, as we will explain soon.

Now, mark the centre of the stairs and sit the two stringers at the same distance, generally the top flange of the stringers would be level or one inch below the existing floor, which will be your last step. Temporary fix the two stringer with a small coach screw each at the distance that you have worked out, these screws are only temporary but they should be strong enough to hold the weight of the stringers easily; now if you are using concrete treads you virtually need to fit the top tread on the two stringer, you need to do this because the holes for the bolts of the concrete treads most time are not in line with the holes on the flange that holds the treads, then fit also your bottom tread on the stringers. If everything has been marked right the treads should be level both ways (level the full length and level across) and the top tread should be the same height as the rest of the stairs, if they don’t work out the first time make any adjustment necessary. Once you have achieved that you can fix the top flange properly with larger coach screws or bolts.

Now that we have fixed the top of the stairs to the existing building, we need to fix the bottom with bolts or concrete. So, let us assume that we have to concrete the two legs of the steel stringers; here we need to make sure that we have dug deep enough and there will be about 6 inches of concrete under the stringer leg and also that the holes we have dug allows about 4 inches of concrete around the legs. Here we need to say that if the bottom treads that you have placed at the beginning to get the right distance between the stringers is in the way, you need to change it one step higher, but keep it as close as possible at the bottom, just because the stringers might move and then you will not be able to fit the rest of the concrete treads, in fact, if it is possible and you can think of something that can temporary hold the weight of the entire set of stairs, then you may as well place all the treads on except the bottom one and then concrete, after concreting you can also fit the last tread and the job is done.

------------------------------------

Other repairs or renovations

For instance here in Queensland most houses have a roof over their patio (veranda) most houses have too much space for verandas, (these are spaces that have a roof on them but they are open and have a handrail around for safety reasons if the building if off the ground) so, if an owner feels like that he is short of space in the house and he needs a small room for the kids or a study, he can enclose some of the veranda space and have an additional room at this house, because there is no structural alterations and the roof is already there, this can be a D.I.Y. job, as long as you know enough how to do it. Anyhow, this is just an example how easy it is to do some repairs or small alterations to these timber houses.

This is all for this time. See you next time with our article, house renovating.

working

This website uses cookies

As a user in the EEA, your approval is needed on a few things. To provide a better website experience, hubpages.com uses cookies (and other similar technologies) and may collect, process, and share personal data. Please choose which areas of our service you consent to our doing so.

For more information on managing or withdrawing consents and how we handle data, visit our Privacy Policy at: https://corp.maven.io/privacy-policy

Show Details
Necessary
HubPages Device IDThis is used to identify particular browsers or devices when the access the service, and is used for security reasons.
LoginThis is necessary to sign in to the HubPages Service.
Google RecaptchaThis is used to prevent bots and spam. (Privacy Policy)
AkismetThis is used to detect comment spam. (Privacy Policy)
HubPages Google AnalyticsThis is used to provide data on traffic to our website, all personally identifyable data is anonymized. (Privacy Policy)
HubPages Traffic PixelThis is used to collect data on traffic to articles and other pages on our site. Unless you are signed in to a HubPages account, all personally identifiable information is anonymized.
Amazon Web ServicesThis is a cloud services platform that we used to host our service. (Privacy Policy)
CloudflareThis is a cloud CDN service that we use to efficiently deliver files required for our service to operate such as javascript, cascading style sheets, images, and videos. (Privacy Policy)
Google Hosted LibrariesJavascript software libraries such as jQuery are loaded at endpoints on the googleapis.com or gstatic.com domains, for performance and efficiency reasons. (Privacy Policy)
Features
Google Custom SearchThis is feature allows you to search the site. (Privacy Policy)
Google MapsSome articles have Google Maps embedded in them. (Privacy Policy)
Google ChartsThis is used to display charts and graphs on articles and the author center. (Privacy Policy)
Google AdSense Host APIThis service allows you to sign up for or associate a Google AdSense account with HubPages, so that you can earn money from ads on your articles. No data is shared unless you engage with this feature. (Privacy Policy)
Google YouTubeSome articles have YouTube videos embedded in them. (Privacy Policy)
VimeoSome articles have Vimeo videos embedded in them. (Privacy Policy)
PaypalThis is used for a registered author who enrolls in the HubPages Earnings program and requests to be paid via PayPal. No data is shared with Paypal unless you engage with this feature. (Privacy Policy)
Facebook LoginYou can use this to streamline signing up for, or signing in to your Hubpages account. No data is shared with Facebook unless you engage with this feature. (Privacy Policy)
MavenThis supports the Maven widget and search functionality. (Privacy Policy)
Marketing
Google AdSenseThis is an ad network. (Privacy Policy)
Google DoubleClickGoogle provides ad serving technology and runs an ad network. (Privacy Policy)
Index ExchangeThis is an ad network. (Privacy Policy)
SovrnThis is an ad network. (Privacy Policy)
Facebook AdsThis is an ad network. (Privacy Policy)
Amazon Unified Ad MarketplaceThis is an ad network. (Privacy Policy)
AppNexusThis is an ad network. (Privacy Policy)
OpenxThis is an ad network. (Privacy Policy)
Rubicon ProjectThis is an ad network. (Privacy Policy)
TripleLiftThis is an ad network. (Privacy Policy)
Say MediaWe partner with Say Media to deliver ad campaigns on our sites. (Privacy Policy)
Remarketing PixelsWe may use remarketing pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to advertise the HubPages Service to people that have visited our sites.
Conversion Tracking PixelsWe may use conversion tracking pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to identify when an advertisement has successfully resulted in the desired action, such as signing up for the HubPages Service or publishing an article on the HubPages Service.
Statistics
Author Google AnalyticsThis is used to provide traffic data and reports to the authors of articles on the HubPages Service. (Privacy Policy)
ComscoreComScore is a media measurement and analytics company providing marketing data and analytics to enterprises, media and advertising agencies, and publishers. Non-consent will result in ComScore only processing obfuscated personal data. (Privacy Policy)
Amazon Tracking PixelSome articles display amazon products as part of the Amazon Affiliate program, this pixel provides traffic statistics for those products (Privacy Policy)
ClickscoThis is a data management platform studying reader behavior (Privacy Policy)